C-Cleats™ & T-Cleats™

Engineered For Performance

Cleats
Intensive development efforts have produced this high performance range of cam cleats that provides unbeatable holding power while allowing easy cleating and releasing of control lines and sheets.

Carbon cam C-Cleats™
C-Cleats™ feature lightweight, ultra-rigid, carbon fibre composite cams that are corrosion free, wear resistant and non-abrasive.

T-Cleats™
T-Cleats™ have hard wearing glass fibre reinforced cams for reliable cleating. They offer a great value solution for moderately demanding applications.

Advanced composite base
Cleat bases are produced from long fibre reinforced polymer to save weight while providing essential stiffness.

Slotted bearings
Self-lubricating, self-cleaning slotted bearings provide lower frictional resistance, quicker response times and superior resistance to sand and salt than ball bearings which can deform under load.
Multi-coil spring
The multi-coil spring recessed in the upper part of the cam generates near constant torque. This consistency ensures secure cleating of even the smallest diameter lines with minimal abrasion or rope wear.
Unique teeth and entry profiles
Low effort line entry and exit due to unique teeth and entry geometry.

Customisation
A comprehensive range of specialist cleat accessories allow customisation of the cleat setup to optimise performance by controlling inward lead, outward lead, cleating and uncleating angle and height.
Total control
Swivel cleat bases further enhance the function of cleats providing articulation, and with some models setting of cleating angle and direction (up or down cleating) to allow control of lines and sheets to and from various positions on the boat.
machined drum
Carbon fibre cam C-Cleat™
Sliderod cars
Design optimisation
Rotation stop accessory
Top swivel
Effective slotted bearings
Top-down models
Multi-coil spring

Low line entry effort
clevis pins Advanced composite base
line guide
RF7 swivel cleat base
Constrictor

Textile Rope Clutch

Unlike conventional clutches the Constrictor® system does not crush the rope between two metal surfaces. Instead, the loaded rope is held securely in a textile sleeve, itself attached to a base unit. The rope runs freely through the sleeve in one direction, but is gripped instantly when running out in the opposite direction. This patented "constrictor effect", provides greater holding power as the load increases.
Bi-conical titanium ring
The patented textile sleeve element is locked in place between a titanium ring and the base unit. The unique conical geometry allows easy insertion of the rope, and ensures that the sleeve is perfectly integrated with the alloy base unit in supporting the applied load.
Controlled holding power
Pulling on the Dyneema® lanyard retracts the sleeve, relaxing the grip on the rope and allowing it to run freely in either direction. The lanyard can be fixed in the V-notch of the base unit to hold the Constrictor® in the open position. Releasing the lanyard allows the sleeve to be drawn to its extended position by a shock cord, constricting the rope in a firm, secure grip.
Buy now on Special Rig
Constrictor

Anatomy of the Constrictor

Stronger and lighter - Twice the holding power and a third of the weight of conventional rope clutches.
Release under load - The line can easily be released under load without the use of a winch simply by pulling the lanyard.
Non destructive - The textile sleeve closes like a constrictor on the line. The extraordinary grip is the result of fibre-to-fibre contact that is far less aggressive than a traditional metal cam, and much more effective.
Structural integration - The Constrictor® is also available in a version suitable for structurally integrated installations. Instead of the notched alloy base unit, the sleeve is supplied with an alloy mounting collar that can be built into a suitably reinforced bulkhead or a customised base fitting.
Remote release - The Dyneema® lanyard can be extended for remote release; for example, to lock a halyard or reefing line to reduce spar compression and minimise rope creep.
Technora® aramid textile sleeve
• Braid Orientation: Cousin Trestec’s experience and expertise in rope manufacture guided the development of the critical braiding angle to maximise grip and minimise slippage.
• Fibre Assembly: Extensive knowledge of fibres combined with laboratory and field testing has resulted in an optimum fibre balance and density for unmatched strength.
• Treatment: A specialised surface treatment plays a critical role in extending the product life, boosting grip and reducing abrasion in stress areas.
Constrictor
Constrictor
Constrictor
Release lanyard in ‘gripping’ position
Constrictor
Release lanyard in ‘open’ position
Constrictor
Structural integration model
Constrictor
Release lanyard knob